How to cut Plexiglass with a table saw? Tips and Tricks

Plexiglass is a popular material that is commonly used in various DIY projects and home improvements. It is a lightweight, shatter-resistant, and versatile material that can be used for windows, skylights, shelves, and other household applications. While cutting plexiglass may seem like a daunting task, it can be easily done with the right tools and techniques. In this article, we will discuss how to cut plexiglass on a table saw, including the use of a diamond saw blade.

Before we dive into the specifics of cutting plexiglass with a table saw, it is important to understand the properties of the material. Plexiglass, also known as acrylic or Perspex, is a thermoplastic material that is susceptible to cracking, melting, or chipping if not cut properly. Therefore, it is important to use the right tools and techniques to avoid damaging the material and ensure a clean and precise cut.

How to cut plexiglass on a table saw

Step 1: Prepare the table saw and the diamond saw blade

To cut plexiglass with a table saw, you will need a few tools and materials, including a table saw with a diamond saw blade, a measuring tape, a straight edge or a T-square, a pencil or marker, and a clamp or a jig. Diamond saw blades are recommended for cutting plexiglass as they are specifically designed to cut hard materials, such as glass, ceramics, and metals. They have small, evenly spaced diamond particles on the blade that grind through the material instead of tearing or chipping it.

Before you start cutting, make sure that the diamond saw blade is installed properly and securely on the table saw. Check the manufacturer’s instructions for the correct blade installation and tighten the blade nut or bolt with a wrench. Make sure that the blade is sharp and clean and that there are no debris or chips on it that could scratch or damage the plexiglass.

Step 2: Measure and mark the plexiglass

To ensure a precise cut, you need to measure and mark the plexiglass accurately. Use a measuring tape to determine the dimensions of the plexiglass sheet and mark the cutting line with a pencil or marker. Use a straight edge or a T-square to draw a straight line along the cutting mark. If you need to make angled or curved cuts, use a compass or a template to mark the cutting line.

Step 3: Secure the plexiglass to the table saw

To prevent the plexiglass from moving or vibrating during the cutting process, it is important to secure it to the table saw with a clamp or a jig. Place the plexiglass sheet on the table saw and position it so that the cutting line is aligned with the blade. Use a clamp or a jig to hold the plexiglass firmly in place and prevent it from shifting or bending.

Step 4: Adjust the blade height and speed

The blade height and speed are crucial factors that determine the quality of the cut and the safety of the process. For cutting plexiglass, it is recommended to set the blade height to the minimum height possible, usually around 1/8 inch or less. This will reduce the risk of the plexiglass cracking or melting due to excessive heat or pressure.

The speed of the blade should also be adjusted according to the thickness of the plexiglass and the type of cut you want to make. For thin sheets of plexiglass, such as those used for picture frames or small windows, a low blade speed of 3000-4000 RPM is recommended. For thicker sheets or more complex cuts, a higher blade speed of 5000-6000 RPM may be necessary. Check the manufacturer’s instructions for the recommended blade speed for cutting plexiglass with a diamond saw blade.

Step 5: Turn on the table saw and make the cut

Once the blade height and speed are adjusted, turn on the table saw and slowly lower the blade onto the plexiglass. Start cutting along the marked line, applying gentle and consistent pressure to guide the plexiglass through the blade. Keep the blade moving at a steady pace and avoid stopping or hesitating in the middle of the cut, as this could cause the plexiglass to melt or crack.

It is also important to keep the blade cool during the cutting process, as the heat generated by the friction could damage the plexiglass or the blade. You can use a lubricant or a cooling agent, such as water or oil, to keep the blade cool and prevent it from overheating. Apply the lubricant or cooling agent to the blade periodically throughout the cutting process, but be careful not to spray it on the plexiglass or the saw table, as this could cause slipping or damage.

Step 6: Finish the cut and clean the edges

Once you have completed the cut, turn off the table saw and carefully remove the plexiglass from the saw table. If the edges of the cut are rough or jagged, you can use sandpaper or a file to smooth them out and make them even. Start with a coarse grit sandpaper, such as 120-grit, and gradually work your way up to a fine grit, such as 400-grit, until the edges are smooth and shiny.

It is also important to clean the edges of the plexiglass after cutting, as they may have accumulated debris, dust, or residue from the cutting process. Use a soft cloth or a paper towel and a mild soap solution to gently clean the edges, taking care not to scratch or damage the surface of the plexiglass. Avoid using harsh or abrasive cleaners, such as ammonia or bleach, as these could cause discoloration or damage to the plexiglass.

Safety tips for cutting plexiglass with a table saw

Cutting plexiglass with a table saw can be a safe and effective process if done properly, but it also involves some risks and hazards that should be taken into account. Here are some safety tips to follow when cutting plexiglass with a table saw:

l Wear protective gear, such as safety glasses, gloves, and a dust mask, to prevent injury from flying debris, dust, or fumes.

l Use a table saw with a blade guard and a riving knife to prevent kickback and blade contact with the plexiglass.

l Avoid cutting too fast or too forcefully, as this could cause the plexiglass to crack or melt.

l Keep your hands and fingers away from the blade and use a push stick or a jig to guide the plexiglass through the saw.

l Keep the saw table and the blade clean and free of debris, as this could affect the accuracy and safety of the cut.

l Use a suitable lubricant or cooling agent to keep the blade cool and prevent overheating.

l Follow the diamond tools manufacturer‘s instructions for the blade height and speed, and make sure to adjust them according to the thickness and type of plexiglass you are cutting.


Cutting plexiglass with a table saw can be a challenging but rewarding process that can yield precise and professional-looking results. By following the right techniques and safety measures, you can cut plexiglass with a diamond saw blade and achieve clean, smooth edges that are suitable for a variety of DIY projects and home improvements. Remember to wear protective gear, secure the plexiglass to the saw table, adjust the blade height and speed, and keep the blade cool and lubricated throughout the cutting process. With practice and patience, you can master the art of cutting plexiglass with a table saw and create stunning pieces that will impress your friends and family.

article source:

Media Contact
Company Name: Binic diamond cutting techniques Ltd
Email: Send Email
Phone: +86 17521277647
Country: China