![\"c126.png\"](\"https:\/\/ecdn6.globalso.com\/upload\/p\/3439\/image_other\/2026-04\/c126-1.png\")
<\/p>\nApplications:<\/p>\n
* This type Soil penetrometer instrument is measure bearing capacity of various soils.<\/p>\n
* With high-horsepower gasoline engines, outdoor use<\/p>\n
* Fully automatic operation, convenient and safe!<\/p>\n
C126 Control panel<\/p>\n
A indicator light is power supply light of digital count meter; B indicator light is Working indicator light of instrument.<\/p>\n
A button is General switch Power supply of instrument; B button is working button of soil penetrometer (set count).<\/p>\n
C button is stop working button of soil penetrometer(set count); D button is working button of single time of soil penetrometer.<\/p>\n
<\/p>\n
Electric Generator Brand: SENKAI SK8500 SE<\/p>\n
Rated voltage: AC220V , AC380V; Rated Power: 7.5 KW (Max: 8 KW)<\/p>\n
Starting mode: Manual start and electric start<\/p>\n
Output volume: 439mL; Output horsepower: 18HP<\/p>\n
Max Power: 15.0\/3600 kw\/rpm; Rated Power: 13.2 \/3600 kw\/rpm<\/p>\n
Max torque: 28.0\/2500 Nm \/rpm<\/p>\n
Engine oil capacity: 1.1 L; Fuel oil capacity: 25 L<\/p>\n
![\"126.png\"](\"https:\/\/ecdn6.globalso.com\/upload\/p\/3439\/image_other\/2026-04\/126-1.png\")
<\/p>\n
Operation:<\/p>\n
1. This electric penetrometer has four lifting seats in four frames, turn the supporting seat counterclockwise, make it vacant, the wheels will be on the ground, using the tractors or manpower to transport the machine to workplace. The traction speed for this machine should not be no more than 30km\/h, long distance transport should been car transport.<\/p>\n
2. Keep the machine steady, then turn lifting seats clockwise , make it touch the ground, and let the wheels not touching the ground , Put the plate holder under the lifting seats. When the ground is harder, put down the four feet available. When the ground was soft, the four circular pad should be put under four feet to prevent the loose soil.<\/p>\n
3. Make sure that the three terminals on the controller and the power cord gasoline generator set correctly connected: mark with number 1-1,2-2.3-3. The air outlet on the controller with aviation plug on the penetrometer correspondence plugged in, 1-1,2-2.3-3.<\/p>\n
4. Adjust the accelerator and throttle, repeatedly pulling the engine about 10-20 times, turn the ignition key and start the generator, if it cannot be start, you should turn off the ignition key, readjust the accelerator and throttle, restart it.<\/p>\n
Attention: Power should be off if the generator was not under working.<\/p>\n
The oil generator should change regularly, which could refer to the manual application for the generator.<\/p>\n
5. Move up the switch, to make sure penetrometer shelves rise, until then it can connect with the probe, at the same time, put the safety lever on the right position, to make sure that the penetrometer shelves will not fall down.<\/p>\n
6. When setting the first feeler lever, please make sure that the angle iron was put on the main stand, which is made for finding the right positon.<\/p>\n
Install the feeler lever (with the probe) into the connecter of the penetrometer.When setting the feeler lever, first of all, connect the feeler lever with the joint, then make the feeler lever connector into the joint under the hammer, After settled it, Downward the switch, and slowly drop the hammer holder, at the same time, make mention of the chain rack hammer down turn also, will go to the bottom of the chain clamp, then can be stop, finally, remove the angle iron.<\/p>\n
![\"126c.png\"](\"https:\/\/ecdn6.globalso.com\/upload\/p\/3439\/image_other\/2026-04\/126c.png\")
<\/p>\n
7. After laying the first feeler lever, go back to step 3, rise hammer shelves, settle the second feeler lever, then refer to the steps above, repeat the above steps.<\/p>\n
8. Set the controller to the desired number of hammer, press the start button to work<\/p>\n
9. When operating the injection, make sure the hammer to fall down as 76mm of height, and record the injection depth from time to time, and record the times of the hammer hit on every single 10cm by N<\/p>\n
10. According to the experimental data analysis, sorting penetrometer blow count and capacity in sand foundation correspondence.<\/p>\n
11. After done the test, pull out the feeler lever, move up e the shelf hammering on a certain height level, disconnecting the probe head, mounted on the probe lifting rings, remove the instrument, pull out the iron rings by man power or by crane.<\/p>\n
![\"5_\u526f\u672c.png\"](\"https:\/\/ecdn6.globalso.com\/upload\/p\/3439\/image_other\/2026-04\/5_copy.png\")
<\/p>\n
12. Maintenance:<\/p>\n
1. Before getting started the machine, please do the lubrication for the chain, rails, etc. Lubricate them for every single two hour.<\/p>\n
2. When raising the hammer shelf, loading and unloading probe, it is necessary to gear hammer rod very well, to make sure the safety of the operation.<\/p>\n
3. According to the frequency of the instrument is working regularly for two motors replace the gear oil.<\/p>\n
Notes:<\/p>\n
* Please set this type instrument on a flat table.<\/p>\n
* Keep clean of the gears so that do not danger gear.<\/p>\n
* Please regular service and prevent rust.<\/p>\n
* Take the average of the three record.<\/p>\n
* our this produst is meeting ASTM standards.<\/p>\n
For more information on the technical parameters or applicable scenarios, please contact us using the following information. We will provide you with customized solutions.<\/p>\n
Media Contact<\/span> Applications: * This type Soil penetrometer instrument is measure bearing capacity of various soils. * With high-horsepower gasoline engines, outdoor use * Fully automatic operation, convenient and safe! C126 Control panel A indicator light is power supply light of digital … Continue reading
Company Name:<\/strong> Xi’an Zealchon Electronic Technology Co., Ltd.<\/a>
Email:<\/strong> Send Email<\/a>
Country:<\/strong> China
Website:<\/strong> https:\/\/www.zealchontest.com\/<\/a><\/p>\n<\/p>\n","protected":false},"excerpt":{"rendered":"